Snap-on 5000-ST Manuale Utente Scaricare il pdf (Pagina 37)

Home
Snap-On
Attrezzi
5000-ST
Manuale Utente

Scaricare
Condividere

Condivisione
Aggiungi ai miei manuali
Stampa

TORQUE CALIBRATION SYSTEM SETUP CHAPTER 4

4-1

Figure 4-1: Power Tool Test Setup

A – Power Tool

B – Joint Rate Simulator

C – Transducer

7. Couple the power tool to the joint rate simulator using the appropriate accessory adaptors

and bit.

8. While holding the power tool drive perfectly in-line with the transducer drive, energize

the tool until its motor stalls or, if featured, the tool clutch slips.

9. Remove the power tool. Loosen the joint rate simulator load screw.

10. Repeat steps 7 through 9 twice again to exercise the tool-simulator assembly and the

SURETEST transducer.

11. Remove the power tool from the loader-transducer and press Zerotare.

12. Press Select Mode to select POWER (TOOL) mode.

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 73 74

TABLE OF CONTENTS 2
Using this Manual 4
CAUTION 5
Read All Instructions 6
PRODUCT DESCRIPTION 8
Introduction 9
Functional Descriptions and 11
Specifications 11
Base Unit 12
FRONT PANEL 13
SURETEST DISPLAY 14
Power Up Sequence 14
Setup Mode 15
5. Auto Settings 16
3. Select Language 16
4. Manufacturer’s Defaults: 16
6. Edit Limits 17
7. Clock Adjust 17
8. Calibration 17
+/-100 mV 19
F- PRINTER PORT (DB-9P) 20
G- OPTIONAL (DB-9P) 20
SURETEST Transducers 21
Serial Communications 23
Manual Loader Specifications 24
SETUP AND PROGRAMMING 25
Back panel connections 26
Base Unit Controls 27
Setting up Date and Time 29
Set-up AUTO CLEAR 30
DATA LIST Memory 31
SURETEST TORQUE CALIBRATION 33
SYSTEM SETUP 33
WARNING 34
Example: 35
Testing Power Tools 36
Non-Impact Tools 36
SPC PRINT-OUT 40
Displaying Data List 42
Calibration 43
Mounting Details 44
Torque Under 250 ft lb 45
Torque Over 250 ft lb 45
Quick Check 47
2000-12-02 49
2000-13-02 49
2000-14-02 49
2000-400-02 49
Torque Calibrations 50
Calibration CW: 51
Calibration CCW: 53
Procedure 54
Calibrate tester 55
Gravitational Effects 57
(2000-600-02) 58
Functional Description 60
Torque Tester/Calibrator 60
A- Transducer Mounting 61
IMPORTANT 62
Loader Rear Panel Controls 63
A- Fuse 63
B- Voltage Select 63
C- AC Power Input 63
D- Solenoid Control 63
Ball Handle Adaptor 64
A- Quick Release Pins 65
C & D- Bracket Knobs 65
E- 4-in-1 Adapter Bracket 66
Extension Arm (Accessory) 67
Torque Driver Testing 68
Torque Multiplier Testing 68
Appendix A 68
Accessories 68
ACCESSORIES APPENDIX A 69
2000-100-02* Roll cabinet 70
Calibration Accessories 73

Commenti su questo manuale

Nessun commento

Snap-on 5000-ST Manuale Utente Pagina 37

Commenti su questo manuale

Prodotti e manuali riguardandi Attrezzi Snap-on 5000-ST